» Analog Voice Ports

EnsurepassHere you will find answers to CVoice – Analog Voice Port Questions Question 1 Refer to the exhibit for IP addresses and telephone numbers. You are working with a customer opening a small sales office in Atlanta. You want the user in Atlanta to be able to dial into the PBX in New York over the IP WAN. The New York PBX uses ground start, a two-wire operation, and DTMF dialing. Choose the correct FXO port configuration commands for New York. A. voice-port 1/0/0 signal ground-start Read more […]

» Cisco Unified Presence

EnsurepassHere you will find answers to Cisco Unified Presence Questions Question 1 Which two options are features in Cisco Unified Presence? (Choose two) A. IP Phone Messenger B. Native Presence C. BLF speed-dial D. Enterprise Instant Messaging E. BLF speed-dial pickup Answer: A B Question 2 Which two protocols are used by Cisco Unified Presence? (Choose two) A. SIP/SIMPLE B. XMPP C. SCCP D. PPPoX E. IMPP Answer: A B Question 3 Refer to the exhibit. What protocol Read more […]

» Voice Fundamentals

EnsurepassHere you will find answers to CVoice – Voice Fundamental Questions Question 1 Which two codes together make up the number that follows the E.164 recommendation numbering scheme? (Choose two) A. country code B. subscriber code C. national destination code D. provider code Answer: A B Explanation E.164 is an international numbering plan created by the International Telecommunication Union (ITU). Each number in the E.164 numbering plan contains the following components: Country Read more […]

» Traditional Telephony

EnsurepassHere you will find answers to Traditional Telephony Questions Question 1 Refer to the exhibit. Which identifies the amplitude of an analog signal stream? A. A B. B C. C D. A & C E. Voltage/Time F. Voltage/Time x B/C Answer: C Question 2 Which three characteristics apply to ISDN PRI? (Choose three) A. The D channel is 16 kbps B. The D channel is 64 kbps C. Can carry data, voice, or video D. Cannot support call forwarding E. Commonly used only in Europe F. Can carry Read more […]

» Cisco Unified Communications Manager 2

EnsurepassHere you will find answers to Cisco Unified Communications Manager Questions – Part 2 Question 1 In which two locations can an end user configure their Call Forward All settings? (Choose two) A. Cisco Unified Serviceability B. Cisco Unified Communications Manager User Options Interface C. Directly on the Cisco Unified IP phone D. Cisco Unified Communications Manager Administration E. Cisco Unified User Serviceability Answer: B C Question 2 What is the quickest way to test Read more […]

» Cisco Unified Communications Manager

EnsurepassHere you will find answers to Cisco Unified Communications Manager Questions – Part 1 Question 1 An administrator wants to locate and remove all unassigned directory numbers on the Cisco Unified Communications Manager system. Which method is the best method to accomplish this task? A. Choose Device > Phone. Search all phones and remove the undesired directory numbers. B. Use the Dial Plan Installer to remove the directory numbers. C. Use the Disaster Recovery System to restore Read more […]

» IP Phone Questions

EnsurepassHere you will find answers to IP Phone Questions Question 1 When troubleshooting a phone that is unable to get an IP address from a DHCP server, what is the first thing to check for on the phone? A. Make sure that DHCP Enabled is disabled on the phone. B. Make sure that the phone is getting the proper VLAN information. C. Make sure that the TFTP server address is correct on the phone. D. Make sure that the DHCP scope has enough addresses left in the range. E. Make sure the phone Read more […]

» Voice Fundamentals

EnsurepassHere you will find answers to CCNA Voice 640-460 Voice Fundamental Questions Question 1 Which type of voice port will allow the gateway to terminate 23 or 30 circuits from the PSTN or a PBX? A. FXO B. FXS C. PRI T1/E1 D. E&M E. BRI Answer: C Explanation The ISDN E1 PRI has 32 timeslots (channels). Each timeslot is 8 bits and has a data rate of 64,000 bits/second. Timeslot 0 is used for frame synchronization and alarms. Timeslot 16 is used for signaling so we can use 30 Read more […]

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com