[Free] 2019(Nov) EnsurePass Juniper JN0-102 Dumps with VCE and PDF 381-390

Get Full Version of the Exam

Question No.381

Which two commands will provide the current configuration of the MX1-PE1 BGP group on your router? (Choose two.)

  1. user@router# show groups | display set | match MX1-PE1

  2. user@router# show | display set | match MX1-PE1

  3. user@routergt; show configuration | match set | match MX1-PE1

  4. user@routergt; show configuration | dispaly set | match MX1-PE1

Correct Answer: BD

Question No.382

The PFE receives which two tables from the RE? (Choose two.)

  1. Layer 5 forwarding table

  2. Layer 2 forwarding table

  3. Layer 3 forwarding table

  4. Layer 4 forwarding table

Correct Answer: BC

Question No.383

What is the network ID address of the IPv4 subnet that includes the IP address





Correct Answer: C

Question No.384

Which command allows you to view the raw packet data of interface ge-1/0/5?

  1. monitor interface traffic ge-1/0/5

  2. monitor traffic interface ge-1/0/5

  3. show interface ge-1/0/5 media

  4. show interface ge-1/0/5 extensive

Correct Answer: B

Question No.385

Click the Exhibit button. Referring to the exhibit, which next-hop interface will be used to reach

the destination?


A. ge-0/0/1.0 B. ge-0/0/0.0 C. ge-0/0/3.0 D. ge-0/0/2.0

Correct Answer: A

Question No.386

Which statement is correct about logical units on Juniper Router interfaces?

  1. Logical units are used only when a Layer 2 identifier is present such as a VLAN.

  2. A logical unit of 0 is required when using a frame-relay DLCI.

  3. A logical unit is always required.

  4. Logical units are not required unless ATM or 802.1Q VLAN tagging is configured.

Correct Answer: C


Many router vendors refer to a logical unit as a subinterface; they do not require a subinterface on every physical interface, whereas a Juniper Networks router does. Note: All router interfaces that will send and receive transit traffic require a logical unit to be configured. This logical unit creates a division of the physical interface into multiple parts.

References: https://www.safaribooksonline.com/library/view/junos- enterpriserouting/9781449309633/ch04s03.html

Question No.387

What are three valid software release designations for the junos OS? (Choose three.)

  1. X

  2. R

  3. T

  4. Z

  5. B

Correct Answer: ABE

Question No.388

Which of the following commands will configure the maximum transmission unit size of a fast Ethernet interface?

  1. set interfaces fe-0/0/0 unit 0 ethernet-options mtu 1200

  2. set interfaces fe-0/0/0 mtu 1200

  3. set interfaces fe-0/0/0 unit 0 mtu 1200

  4. set interfaces fe-0/0/0.0 mtu 1200

Correct Answer: C

Question No.389

Which word starts a command to display the operational status of a Junos device?

  1. put

  2. set

  3. show

  4. get

Correct Answer: C

Question No.390

What are three interface prefixes for a 40-gigabit interface? (Choose three.)

  1. et

  2. es

  3. fte

  4. xe

  5. xle

Correct Answer: ABE

Get Full Version of the Exam
JN0-102 Dumps
JN0-102 VCE and PDF

You must be logged in to post a comment.

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com