[Free] 2019(Nov) EnsurePass Juniper JN0-102 Dumps with VCE and PDF 201-210

Get Full Version of the Exam
http://www.EnsurePass.com/JN0-102.html

Question No.201

Which statement is true about the forwarding table?

  1. The forwarding table is stored in the control plane only.

  2. The forwarding table is stored in the control plane and in the forwarding plane.

  3. The forwarding table contains both active and inactive routes.

  4. The forwarding table can contain only a single next hop per destination.

Correct Answer: B

Question No.202

What represents the binary equivalence of 148?

A.

10010110

B.

11010010

C.

10011100

D.

10010100

Correct Answer: D

Question No.203

Exhibit

user@routergt; show route

inet.0: 9 destinations, 9 routes (9 active, 0 holddown, 0 hidden)

= Active Route, – = Last Active, * = Both 10.10.10.91/32 *[Direct/0] 00:09:40

gt;via lo0.0

10.10.10.92/32 *[OSPF/10] 00:01:50, metric 1

gt;to 172.16.1.2 via ge-0/0/2.0

100.100.1.0/24 *[Static/5] 00:01:50

Reject

172.16.1.0/24 *[Direct/0] 00:06:09

gt;via ge-0/0/2.0

172.16.1.1/32 *[Local/0] 00:06:09

Local via ge-0/0/2.0

192.168.0.0/16 *[Aggregate/130] 00:00:06

Reject

192.168.0.0/17 *[Aggregate/130] 00:00:06

gt;to 172.16.1.2 via ge-0/0/2.0 192.168.50.0/24 *[Static/5] 00:00:06

gt;to 172.16.1.2 via ge-0/0/2.0 192.168.51.0/24 *[Static/5] 00:00:06

gt;to 172.16.1.2 via ge-0/0/2.0

user@routergt; show configuration policy-options policy-statement demo {

term 1 { from {

protocol static;

route-filter 192.168.0.0/16 orlonger accept;

}

then accept;

}

}

user@routergt; show configuration protocols ospf export demo;

area 0.0.0.0 { interface ge-0/0/2.0;

}

Exhibit

Given the configuration and routing table shown in the exhibit, which routes will be advertised to OSPF neighbors because of the demo policy?

A. 192.168.0.0/16 only B. 192.168.50.0/24 only

C. 192.168.50.0/24 and 192.168.51.0/24

D. 192.168.0.0/17, 192.168.50.0/24, and 192.168.51.0/24

Correct Answer: C

Question No.204

Which two statements are correct regarding default protocol preference values? (Choose two.)

  1. RIP is preferred over OSPF external routes.

  2. Direct, local, and static routes have the same preference value.

  3. OSPF#39;s preference value is lower than BGP.

  4. OSPF has a single preference value for both internal and external routes.

Correct Answer: AC

Question No.205

Exhibit [editsnmp] user@router# show

communityCommunityA { authorization read-only; clients {

192.168.1.0/28;

}

}

trap-groupgroupA { categories {

link;

}

targets {

192.168.100.1;

192.168.200.1;

}

}

Exhibit

Referring to the exhibit, what is the purpose of the targets section of the configuration?

  1. It defines which devices will be sending traps.

  2. It specifies where to send traps.

  3. It defines the IP addresses of management systems that can access the device.

  4. It specifies which devices can be polled for SNMP data.

Correct Answer: B

Question No.206

Exhibit

user@routergt; show configuration firewall familyinet {

filter demo { term example { from {

source-address { 100.100.100.0/24;

}

destination-address { 200.200.200.0/24;

}

}

then { reject;

}

}

term testing {

from {

source-address { 10.10.10.0/28;

}

destination-address { 200.200.200.0/24;

}

}

then sample;

}

term results { from { address {

200.200.200.0/24;

}

}

then accept;

}

term final { thenpolicer LAPD;

}

}

}

Exhibit

Given the configuration shown in the exhibit, what will happen to traffic from source 10.10.10.25 destined to 200.200.200.1?

  1. The traffic will be rejected.

  2. The traffic will be dropped.

  3. The traffic will be forwarded.

  4. The traffic will be policed.

Correct Answer: C

Question No.207

Which two commands allow you to return to a previous version of software on the device? (Choose two.)

  1. request system software add

  2. request system software downgrade

  3. request system software replace

  4. request system software rollback

Correct Answer: AD

Question No.208

A network administrator wants to verify the active alarms on interface so-0/0/0.0. Which command displays this information?

  1. show interfaces alarms

  2. show interfaces terse

  3. show alarms extensive

  4. show interfaces extensive

Correct Answer: D

Question No.209

By default, what are three valid routing tables? (Choose three.)

  1. inet.0

  2. inet4.0

  3. inet.6

  4. inet6.0

  5. inet.3

Correct Answer: ADE

Question No.210

Which two protocols use UDP as a transport protocol by default? (Choose two.)

  1. Telnet

  2. ICMP

  3. DHCP

  4. RIP

Correct Answer: CD

Get Full Version of the Exam
JN0-102 Dumps
JN0-102 VCE and PDF

You must be logged in to post a comment.

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com