[Free] 2019(Nov) EnsurePass Cisco 300-360 Dumps with VCE and PDF 31-40

Get Full Version of the Exam
http://www.EnsurePass.com/300-360.html

Question No.31

Which three things do you need to consider prior to performing a wireless site survey? (Choose three.)

  1. The time required to acquire any additional infrastructure components.

  2. The time required to survey each potential AP location.

  3. The time required to assess application server locations at the customer facility.

  4. The type of wireless survey tools required to perform the site survey.

  5. The time required to assess customer WLAN density and throughput requirements.

  6. The time required to utilize the design mode in Cisco WCS to prepare a preliminary WLAN design to reduce on-site survey time.

Correct Answer: BDE

Question No.32

A network engineer is performing a site survey in preparation for an installation. Which three hardware parameters must be inspected? (Choose three.)

  1. routing protocol used

  2. PoE capability

  3. switch STP capability

  4. distance of antenna to communications room

  5. switch port availability

  6. distance of access point to communications room

Correct Answer: BEF

Question No.33

An 802.11n implementation is being discussed. Users are satisfied with the potential 300-450 Mbps throughput of new 802.11n APs. Which three bandwidth requirements are used to calculate per client bandwidth through an 802.11n AP network? (Choose three.)

  1. 450 Mbps throughput is the client max for 5-GHz radio.

  2. Channel bonding on 5 GHz is required for a client to have a 300 Mbps WiFi link.

  3. 300 Mbps throughput is the client max for 2.4-GHz radio.

  4. The remaining bandwidth is divided per device when more clients are connected to one AP.

  5. 100 Mbps Ethernet switch port is a potential bottleneck.

  6. CleanAir helps clear noise for 802.11n channel bonding to work.

Correct Answer: ACE

Question No.34

An engineer is assigned to provide wireless coverage in a provincial capital building. Due to the age and historic nature of the building, the ability to run new copper Ethernet cable to desired AP locations is limited. Which requirement should the engineer specify to overcome this restriction?

  1. Deploy access points where the survey indicates and connect them via fiber optic cable, using a media adapter, and locally provide power.

  2. Deploy access points to each phone location converting two spare pairs of copper from the phone line to Ethernet and locally provide power.

  3. Deploy access point devices where limited cable can be run or exists and connect high- gain antennas and increase Tx power to increase cell size.

  4. Deploy RAP where limited cable can be run or exists, and extend coverage using MAP.

Correct Answer: D

Question No.35

A customer reports that wireless clients are not able to receive multicast data from known working multicast servers on the wired network. The client is connecting at the highest mandatory wireless rate of 24 Mbps and the wireless controller is configured for multicast- unicast mode. What three actions should the engineer take next to troubleshoot the issue? (Choose three.)

  1. verify that the L3 interfaces are configured for pim sparse-dense-mode on the VLAN servicing the wireless access points as well as the wireless controller#39;s management VLAN

  2. change the wireless controller from Multicast-Unicast mode to Multicast-Multicast mode and assign a multicast address in the 239.X.X.X/8 subnet

  3. verify that IGMP snooping is disabled on the wireless controller since the access points are handling IGMP messages from the clients

  4. verify that Global Multicast mode has been enabled

  5. make sure the highest mandatory rate is set to 54 Mbps so that the multicast traffic has sufficient bandwidth

  6. verify Multicast Listener Discovery (MLD) v1 snooping has been enabled to keep track of and

deliver IPv4 multicast flows

Correct Answer: ABD

Question No.36

What is the result if a client radio is incapable of supporting all the 5 GHz channels you have deployed in the controller or APs?

  1. You may only be able to deploy 20 MHz-wide channels.

  2. This may result in the client having to roam more frequently to find a channel it supports.

  3. This may result in coverage holes in the network.

  4. You may only be able to deploy 40 MHz-wide channels.

Correct Answer: C

Question No.37

You must upgrade a data- based wireless network to support Voice over Wireless. Which RSSI measurement do you use to redesign the wireless network?

  1. -65 dBm

  2. -72 dBm

  3. -75 dBm

  4. -67 dBm

Correct Answer: D

Question No.38

When designing and deploying an outdoor mesh network, what is the appropriate RF cell overlap?

  1. 10 percent

  2. 15 percent

  3. 20 percent

  4. 25 percent

  5. Application dependent

Correct Answer: E

Question No.39

During an installation of a wireless network in a country that follows ETSI standards, the customer is requesting to manually set the channels on the 2.4GHz radios. Which channels are recommended for use in this deployment?

A.

52, 56, 60, 64

B.

1, 6, 11, 14

C.

36, 40, 44, 48

D.

1, 5, 9, 13

Correct Answer: C

Question No.40

You are designing an outdoor mesh network to cover several sports fields. The core of the

network is located in a building at the entrance of a sports complex. Which type of antenna do you use with the RAP for backhaul connectivity?

  1. a 5 GHz, 14-dBi patch antenna

  2. a 5 GHz, 8-dBi omnidirectional antenna

  3. a 2.4 GHz, 14-dBi omnidirectional antenna

  4. a 2.4 GHz, 8-dBi patch antenna

Correct Answer: B

Explanation:

The AP1524PS includes three radios: a 2.4 -GHz, a 5.8- GHz, and a 4.9-GHz radio. The 2.4-GHz radio is for client access (non- public safety traffic) and the 4.9-GHz radio is for public safety client access traffic only. The 5.8-GHz radio can be used as the backhaul for both public safety and

non-public safety traffic.

Reference:

https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-6/configuration- guide/b_cg76/b_cg76_chapter_010000001.html

>

Get Full Version of the Exam
300-360 Dumps
300-360 VCE and PDF

You must be logged in to post a comment.

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com