[Free] 2018(Mar) EnsurePass Passguide Cisco 210-065 Dumps with VCE and PDF 251-260

Ensurepass.com : Ensure you pass the IT Exams
2018 Mar Cisco Official New Released 210-065
100% Free Download! 100% Pass Guaranteed!

Implementing Cisco Video Network Devices v1.0

Question No: 251 – (Topic 5)

An engineer is deploying a Cisco TelePresence Touch 8 controller for a Cisco TelePresence SX20. Which two steps are required as part of this process? (Choose two.)

  1. Connect the cable from the Touch 8 controller to the Cisco TelePresence SX20.

  2. Connect the Touch 8 controller to the power adapter and connect the adapter to the network.

  3. Connect the Touch 8 controller to the secondary network adapter on the Cisco TelePresence SX20.

  4. Reboot the Cisco TelePresence SX20.

  5. Hold the mute button down for 20 seconds while you power on the Touch 8 controller.

Answer: C,E

Question No: 252 – (Topic 5)

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

A call with a destination alias of 15551001234 reaches a Cisco TelePresence VCS. Which transform will the destination alias match?

  1. Transform 1

  2. Transform 2

  3. Transform 3

  4. Transform 4

Answer: B

Question No: 253 – (Topic 5)

A video engineer needs to locate the running version of the Cisco VCS. Under which tab in the Cisco VCS web interface is this information contained?

  1. Applications

  2. Status

  3. System

  4. Configuration

Answer: B

Question No: 254 – (Topic 5)

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

You are deploying a Cisco VCS Expressway with the Advanced Networking option key into two separate DMZs. Gateways for all networks are the lowest usable IP address in the subnet. While you are logged in as an admin user, which command should you enter into the CLI, to enable IP routing to the Cisco VCS Control and nothing else on the internal


  1. xConfiguration IP Gateway:

  2. xConfiguration RouteAdd Address: PrefixLength:16 Gateway: Interface: LAN1

  3. xCommand RouteAdd Address: PrefixLength:16 Gateway: Interface: LAN1

  4. xCommand RouteAdd Address: PrefixLength:32 Gateway: Interface: LAN1

Answer: D

Question No: 255 – (Topic 5)

A Cisco TelePresence System 1300 Series endpoint is in the process of booting and the engineer notices a red quot;Xquot; on the screen for Step 6 in the boot process. What does this red quot;Xquot; indicate?

  1. The endpoint failed to load its firmware.

  2. There is an error with compact flash.

  3. The endpoint could not obtain an IP address via DHCP.

  4. The touch panel is malfunctioning.

Answer: B

Question No: 256 – (Topic 5)

An engineer is deploying a Cisco TelePresence Content Server. Which two services are provided by this product? (Choose two.)

  1. video storage

  2. multiconferencing

  3. scheduler

  4. video conferencing

  5. video recording

  6. video overlay

Answer: A,E

Question No: 257 – (Topic 5)

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

A technician is reviewing the search history details on a Cisco TelePresence VCS for a recent call that failed. What was the cause for the call setup failure?

  1. A local call policy rule denied the call.

  2. The source alias matched an entry in the registration deny list.

  3. The originating caller was not authenticated.

  4. The source alias origin is unknown.

Answer: A

Question No: 258 – (Topic 5)

Which of the following first provided centralized call control capabilities for H.323 video endpoints?

  1. Gatekeeper

  2. CUCM

  3. MGCP

  4. MCU

Answer: D

Question No: 259 – (Topic 5)

An engineer is configuring VIP mode for a Cisco TelePresence Multipoint Switch. What are three characteristics the engineer must keep in mind? (Choose three.)

  1. VIP mode can be configured only when the meeting is not active.

  2. The VIP is displayed on the center screen for three screen systems.

  3. Network multipoint meetings are supported.

  4. VIP mode timers must be configured from the CLI.

  5. Locking is not supported.

  6. Only one VIP can be configured for each meeting.

Answer: B,D,F

Question No: 260 – (Topic 5)

An end user using C series codec wants to change the participant layout for a meeting hosted on a Cisco TelePresence Server. What are three valid layout options available in codec web interface? (Choose three.)

  1. single screen

  2. loudest speaker

  3. rolling

  4. equal

  5. custom

  6. overlay

Answer: A,D,F

100% Ensurepass Free Download!
Download Free Demo:210-065 Demo PDF
100% Ensurepass Free Guaranteed!
210-065 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

You must be logged in to post a comment.

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com