[Free] 2018(Mar) EnsurePass Pass4sure Cisco 200-401 Dumps with VCE and PDF 11-20

Ensurepass.com : Ensure you pass the IT Exams
2018 Mar Cisco Official New Released 200-401
100% Free Download! 100% Pass Guaranteed!

Managing Industrial Networks with Cisco Networking

Question No: 11 – (Topic 2)

Which prompt is used to configure parameters for the Ethernet ports of an industrial switch?

  1. Switch(config-if)#

  2. Switch(config-if-ind)#

  3. Switch(config-line)#

  4. Switch(config-ind)#

  5. Switch(config-vlan)#

Answer: A

Question No: 12 – (Topic 2)


Ensurepass 2018 PDF and VCE

Refer to the exhibit. C-router is to be used as a quot;router-on-a-stickquot; to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?

  1. These commands need to be added to the configuration:C-router(config)# router eigrp 123C-router(config-router)# network

  2. These commands need to be added to the configuration:C-router(config)# router ospf 1C-router(config-router)# network area 0

  3. These commands need to be added to the configuration:C-router(config)# router ripC- router(config-router)# network

  4. No further routing configuration is required.

Answer: D

Question No: 13 – (Topic 2)

What are the two most relevant factors in determining the class of administration that is required to maintain the telecommunications infrastructure? (Choose two.)

  1. the size of the infrastructure

  2. the complexity of the infrastructure

  3. the age of the infrastructure

  4. the industry that the infrastructure supports

  5. the physical environment of the infrastructure

Answer: A,B

Question No: 14 – (Topic 2)


Ensurepass 2018 PDF and VCE

Refer to the exhibit. CCNA.com has the industrial network shown in the exhibit. All switches are configured as layer 2 switches and are using VLAN 1 as their management VLAN. Each VLAN 1 interface has been assigned the correct IP address. What is the purpose of assigning a default gateway to SW-C switch?

  1. allows connectivity between the VLAN 1 interface on SW-C and other devices in the network.

  2. allows connectivity between Host A and other devices in the network.

  3. allows connectivity between Host B and other devices in the network.

  4. allows the switch to pass traffic between Host A and Host B

Answer: A

Question No: 15 – (Topic 2)

An administrator has connected devices to an industrial switch and, for security reasons, wants the dynamically learned MAC addresses from the address table added to the running configuration. What must be done to accomplish this?

  1. Enable port security and use the keyword sticky.

  2. Set the switchport mode to trunk and save the running configuration.

  3. Use the switchport protected command to have the MAC addresses added to the configuration.

  4. Use the no switchport port-security command to allow MAC addresses to be added to the configuration.

Answer: A

Question No: 16 – (Topic 2)

Given a ring topology, which loop prevention mechanism provides the fastest reconvergence time after a link failure?

  1. Rapid Per-VLAN Spanning Tree Protocol

  2. Resilient Ethernet Protocol

  3. Multiple Spanning Tree Protocol

  4. Spanning Tree Protocol

Answer: B

Question No: 17 – (Topic 2)

Which two ports does EtherNet/IP use to communicate? (Choose two.)

  1. TCP 44818

  2. UDP 44818

  3. TCP 502

  4. UDP 502

  5. TCP 2222

  6. UDP 2222

Answer: A,F

Question No: 18 DRAG DROP – (Topic 2)

Ensurepass 2018 PDF and VCE


Ensurepass 2018 PDF and VCE

Question No: 19 – (Topic 2)

According to the Purdue Reference Model, at which layer would you perform manufacturing operations and control?

  1. Level 0

  2. Level 1

  3. Level 2

  4. Level 3

  5. Level 4

Answer: D

Question No: 20 – (Topic 2)

Why is SSH preferred over Telnet as a method of accessing a network device to alter or view the configuration?

  1. Telnet encrypts only the login information, not the entire transmission.

  2. SSH requires fewer network resources and no additional configuration.

  3. Telnet is more difficult to use and configure than SSH.

  4. SSH encrypts the login and session information.

Answer: D

100% Ensurepass Free Download!
Download Free Demo:200-401 Demo PDF
100% Ensurepass Free Guaranteed!
200-401 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

You must be logged in to post a comment.

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com