[Free] 2018(Mar) EnsurePass Pass4sure Cisco 200-105 Dumps with VCE and PDF 31-40

Ensurepass.com : Ensure you pass the IT Exams
2018 Mar Cisco Official New Released 200-105
100% Free Download! 100% Pass Guaranteed!

Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)

Question No: 31 – (Topic 1)

You enter the show ipv6 route command on an OSPF device and the device displays a route. Which conclusion can you draw about the environment?

  1. OSPF is distributing IPv6 routes to BGP.

  2. The router is designated as an ABR.

  3. The router is designated as totally stubby.

  4. OSPFv3 is in use.

Answer: A

Question No: 32 – (Topic 1)

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

While troubleshooting a switch, you executed the show interface port-channel 1 etherchannel command and it returned this output. Which information is provided by the Load value?

  1. the percentage of use of the link

  2. the preference of the link

  3. the session count of the link

  4. the number source-destination pairs on the link

Answer: D

Question No: 33 – (Topic 1)

Which Cisco platform can verify ACLs?

  1. Cisco Prime Infrastructure

  2. Cisco Wireless LAN Controller

  3. Cisco APIC-EM

  4. Cisco IOS-XE

Answer: B

Question No: 34 – (Topic 1)

Which option describes the purpose of traffic policing?

  1. It prioritizes routing protocol traffic.

  2. It remarks traffic that is below the CIR

  3. It drops traffic that exceeds the CIR.

  4. It queues and then transmits traffic that exceeds the CIR.

Answer: C Explanation:

Traffic policing allows you to control the maximum rate of traffic transmitted or received on an interface. Traffic policing is often configured on interfaces at the edge of a network to limit traffic into or out of the network. In most Traffic Policing configurations, traffic that falls within the rate parameters is transmitted, whereas traffic that exceeds the parameters is dropped or transmitted with a different priority.

Question No: 35 – (Topic 1)

Which configuration can you apply to enable encapsulation on a subinterface?

  1. interface FastEthernet 0/0 encapsulation dot1Q 30

    ip address

  2. interface FastEthernet 0/0.30

    ip address

  3. interface FastEthernet 0/0.30 description subinterface vlan 30

  4. interface FastEthernet 0/0.30 encapsulation dot1Q 30

ip address

Answer: D

Question No: 36 – (Topic 1)

Which EIGRP for IPv6 command can you enter to view the link-local addresses of the neighbors of a device?

  1. show ipv6 eigrp 20 interfaces

  2. show ipv6 route eigrp

  3. show ipv6 eigrp neighbors

  4. show ip eigrp traffic

Answer: C

Question No: 37 – (Topic 1)

Which three options are the HSRP states for a router? (Choose three.)

  1. initialize

  2. learn

  3. secondary

  4. listen

  5. speak

  6. primary

Answer: B,D,E Explanation:

HSRP States

Ensurepass 2018 PDF and VCE

Question No: 38 – (Topic 1)

Which spanning-tree feature places a port immediately into a forwarding stated?

  1. BPDU guard

  2. PortFast

  3. loop guard

  4. UDLD

  5. Uplink Fast

Answer: B Explanation:

PortFast causes a switch or trunk port to enter the spanning tree forwarding state immediately, bypassing the listening and learning states. You can use PortFast on switch or trunk ports that are connected to a single workstation, switch, or server to allow those devices to connect to the network immediately, instead of waiting for the port to transition from the listening and learning states to the forwarding state.

Question No: 39 – (Topic 1)

Which statement about the IP SLAs ICMP Echo operation is true?

  1. The frequency of the operation .s specified in milliseconds.

  2. It is used to identify the best source interface from which to send traffic.

  3. It is configured in enable mode.

  4. It is used to determine the frequency of ICMP packets.

Answer: D Explanation:

This module describes how to configure an IP Service Level Agreements (SLAs) Internet Control Message Protocol (ICMP) Echo operation to monitor end-to-end response time between a Cisco router and devices using IPv4 or IPv6. ICMP Echo is useful for

troubleshooting network connectivity issues. This module also demonstrates how the results of the ICMP Echo operation can be displayed and analyzed to determine how the network IP connections are performing.

ICMP Echo Operation

The ICMP Echo operation measures end-to-end response time between a Cisco router and any devices using IP. Response time is computed by measuring the time taken between sending an ICMP Echo request message to the destination and receiving an ICMP Echo reply.

In the figure below ping is used by the ICMP Echo operation to measure the response time between the source IP SLAs device and the destination IP device. Many customers use IP SLAs ICMP-based operations, in-house ping testing, or ping-based dedicated probes for response time measurements.

Ensurepass 2018 PDF and VCE

Figure 1. ICMP Echo Operation

http://www.cisco.com/c/dam/en/us/td/i/100001-200000/120001-130000/121001- 122000/121419.ps/_jcr_content/renditions/121419.jpg

The IP SLAs ICMP Echo operation conforms to the same IETF specifications for ICMP ping testing and the two methods result in the same response times.

Configuring a Basic ICMP Echo Operation on the Source Device SUMMARY STEPS

1. enable 2. configure terminal 3. ip sla operation-number 4. icmp-echo

{destination-ip-address | destination-hostname} [source-ip {ip-address | hostname} | source-interface interface-name] 5. frequency seconds 6. end

Question No: 40 – (Topic 1)

Which part of the PPPoE server configuration contains the information used to assign an IP address to a PPPoE client?

  1. virtual-template interface

  2. DHCP

  3. dialer interface

  4. AAA authentication

Answer: C Explanation:

PPPoE is configured as a point to point connection between two Ethernet ports. As a tunneling protocol, PPPoE is used as an effective foundation for the transport of IP packets at the network layer. IP is overlaid over a PPP connection and uses PPP as a virtual dial up connection between points on the network. From the user#39;s perspective, a PPPoE session is initiated by using connection software on the client machine or router. PPPoE session initiation involves the identification of the Media Access Control (MAC) address of the remote device. This process, also known as PPPoE discovery

100% Ensurepass Free Download!
Download Free Demo:200-105 Demo PDF
100% Ensurepass Free Guaranteed!
200-105 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

You must be logged in to post a comment.

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com