300-410 Real Exam Dumps Questions and answers 41-50

Get Full Version of the Exam
http://www.EnsurePass.com/300-410.html

Question No.41

An engineer is trying to copy an IOS file from one router to another router by using TFTP. Which two actions are needed to allow the file to copy? (Choose two.)

  1. Copy the file to the destination router with the copy tftp: flash: command

  2. Enable the TFTP server on the source router with the tftp-server flash: lt;filenamegt; command

  3. TFTP is not supported in recent IOS versions, so an alternative method must be used

  4. Configure a user on the source router with the username tftp password tftp command

  5. Configure the TFTP authentication on the source router with the tftp-server authentication local command

Correct Answer: AB

Question No.42

Refer to the exhibit. Which control plane policy limits BGP traffic that is destined to the CPU to 1 Mbps and ignores BGP traffic that is sent at higher rate?

image

  1. policy-map SHAPE_BGP

  2. policy-map LIMIT_BGP

  3. policy-map POLICE_BGP

  4. policy-map COPP

Correct Answer: D

Question No.43

Refer to the exhibit. Users report that IP addresses cannot be acquired from the DHCP server. The DHCP server is configured as shown. About 300 total nonconcurrent users are using this DHCP server, but none of them are active for more than two hours per day. Which action fixes the issue within the current resources?

image

  1. Modify the subnet mask to the network 192.168.1.0 255.255.254.0 command in the DHCP pool

  2. Configure the DHCP lease time to a smaller value

  3. Configure the DHCP lease time to a bigger value

  4. Add the network 192.168.2.0 255.255.255.0 command to the DHCP pool

Correct Answer: B

Question No.44

Refer to the exhibit. ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console. Which command is missing from the IP SLA configuration?

image

  1. Start-time 00:00

  2. Start-time 0

  3. Start-time immediately

  4. Start-time now

Correct Answer: D

Explanation:

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipsla/configuration/15-mt/sla-15-mt- book/sla_icmp_echo.html

Question No.45

Refer to the exhibit. An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock. What is the reason for this error?

image

  1. An authentication error with the NTP server results in an incorrect timestamp.

  2. The keyword localtime is not defined on the timestamp service command.

  3. The NTP server is in a different time zone.

  4. The system clock is set incorrectly to summer-time hours.

Correct Answer: B

Question No.46

A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap. Which command allows the logging on the switch to show the time of the flap according to the clock on the device?

  1. service timestamps log uptime

  2. clock summer-time mst recurring 2 Sunday mar 2:00 1 Sunday nov 2:00

  3. service timestamps log datetime localtime show-timezone

  4. clock calendar-valid

Correct Answer: C

Question No.47

When provisioning a device in Cisco DNA Center, the engineer sees the error message 鈥淐annot select the device. Not compatible with template鈥? What is the reason for the error?

  1. The template has an incorrect configuration.

  2. The software version of the template is different from the software version of the device.

  3. The changes to the template were not committed.

  4. The tag that was used to filter the templates does not match the device tag.

Correct Answer: D

Explanation:

https://www.cisco.com/c/en/us/td/docs/cloud-systems-management/network-automation-and- management/dna-center/1-2- 10/user_guide/b_cisco_dna_center_ug_1_2_10/b_dnac_ug_1_2_10_chapter_0111.html

Question No.48

While working with software images, an engineer observes that Cisco DNA Center cannot upload its software image directly from the device. Why is the image not uploading?

  1. The device must be resynced to Cisco DNA Center.

  2. The software image for the device is in install mode.

  3. The device has lost connectivity to Cisco DNA Center.

  4. The software image for the device is in bundle mode.

Correct Answer: B

Explanation:

https://www.cisco.com/c/en/us/td/docs/cloud-systems-management/network-automation-and- management/dna-center/1-2- 10/user_guide/b_cisco_dna_center_ug_1_2_10/b_dnac_ug_1_2_10_chapter_0100.html

Question No.49

An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install. Which command must the engineer run to correct the configuration?

  1. sudo maglev-config update

  2. sudo maglev install config update

  3. sudo maglev reinstall

  4. sudo update config install

Correct Answer: A

Question No.50

Refer to the exhibit. An administrator that is connected to the console does not see debug messages when remote users log in. Which action ensures that debug messages are displayed for remote logins?

image

  1. Enter the transport input ssh configuration command.

  2. Enter the terminal monitor exec command.

  3. Enter the logging console debugging configuration command.

  4. Enter the aaa new-model configuration command.

Correct Answer: C

Get Full Version of 300-410 Dumps

You must be logged in to post a comment.

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com