[Free] 2017(Nov) Dumps4cert Pass4sure Cisco 300-360 Dumps with VCE and PDF 1-10

Dumps4cert
2017 Nov Cisco Official New Released 300-360
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4cert.com/300-360.html

Designing Cisco Wireless Enterprise Networks

Question No: 1

When designing a WLAN, AP placement is important. Which option describes how to rank the density of APs needed to support location services versus data and voice services?

  1. Data services have the lowest density of APs compared to location services, which has the highest density.

  2. Data services have a lower density of APs compared to location services, but more than voice.

  3. Voice services have the highest density of APs over location and data services.

  4. Voice and data services require a higher density of APs than location services.

Answer: A

Question No: 2

A network engineer is configuring QoS with a DSCP value of 46. To which queue must the CoS be mapped for priority queuing of the voice frames?

  1. 1

  2. 2

  3. 5

  4. 4

  5. 3

Answer: C

Question No: 3

An engineer is preparing for an indoor wireless LAN survey and is provisioning a survey kit. Which three pieces of equipment should be included? (Choose three.)

  1. external connector access point

  2. integrated antenna access point

  3. coax low-loss cable

  4. battery operated power supply

  5. range finder

  6. Yagi antennas

Answer: B,D,E

Question No: 4

What is the optimal distance between APs for location services without considering the physical environment?

  1. 10 to 25 feet

  2. 90 to 120 feet C. 50 to 70 feet

  3. 80 to 100 feet

Answer: C

Reference: http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob41dg/emob41dg- wrapper/ ch13Loca.html

Question No: 5

An engineer is tuning RRM parameters to improve client connectivity. Which channel band results in the best 802.11n client compatibility?

  1. UNII-2

  2. UNII-2e

  3. UNII-3

  4. UNII

  5. UNII-1

Answer: E Explanation:

802.11n operates on the same channel as 802.11a. For better compatibility with 802.11n clients, it is recommended to stay on lower channels (UNII-1 band).

Reference: http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-

controllers/108184config-802-11n-wlc.html

Question No: 6

When reviewing a design for a voice over wireless deployment, what per-call bandwidth cost should be factored in when determining maximum calls per cell using SIP and G.711u as the codec?

  1. 64 bytes B. 8 bytes

  2. 80 bytes

  3. 10 bytes

Answer: C

Question No: 7

The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm. What is the target value for the cell edge reading?

  1. -62 dBm

  2. -67 dBm

  3. -60 dBm

  4. -70 dBm

Answer: B

Question No: 8

A customer is deploying a mesh outdoor wireless network based on FCC standards where spectrum analysis shows significant radar energy propagating throughout the coverage area from a local weather station. Which channel must be excluded from the access points RRM calculation to avoid network disruption due to weather radar activity?

A. 132

  1. 44

  2. 11

  3. 36

Answer: A Explanation:

Weather radars operate within the 5600- to 5650-MHz band, which means that channels 124 and 128 might be affected, but also channels 120 and 132 might suffer from weather radar activity.

Reference: http://www.cisco.com/c/en/us/td/docs/wireless/technology/mesh/7-

3/design/guide/Mesh/ Mesh_chapter_0111.html

Question No: 9

An engineer is deploying an outdoor Mesh network. Which four major factors should be considered? (Choose four.)

  1. power

  2. buildings

  3. traffic lights

  4. satellite dishes

  5. line of sight

  6. network connectivity

  7. power lines

  8. mounting

Answer: A,E,F,H

Question No: 10

An engineer receives a digital image scanned from the floor plans of a facility to be surveyed for wireless survey and imported it into Air Magnet Pro. However, the document contains no scale. Which action can the engineer take to most accurately calibrate the size of the floor plan in Air Magnet?

  1. Mark the length of a hallway, then count the ceiling tiles, multiply that number by 2 and enter that value.

  2. Zoom in and mark across a hallway, then count the floor tiles across that hallway and enter that value.

  3. Zoom in and mark a doorway, then size it at 3 feet because most doorways are 36 inches.

  4. Mark the entire longest dimension of the floorplan, then use Google Earth to measure the correspondingoutside dimension and enter that value.

Answer: D

100% Free Download!
Download Free Demo:300-360 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4cert 300-360 Full Exam PDF and VCE

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4cert IT Certification PDF and VCE

You must be logged in to post a comment.

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com