[Free] 2017(Apr) Ensurepass Testking Cisco 300-135 Latest Dumps 51-60

Ensurepass
2017 April Cisco Official New Released 300-135 Q&As
100% Free Download! 100% Pass Guaranteed!
http://www.ensurepass.com/300-135.html

Troubleshooting and Maintaining Cisco IP Networks (TSHOOT)

 

QUESTION 51

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to switch technology?

 

A.

NTP

B.

Switch-to-Switch Connectivity

C.

Loop Prevention

D.

Access Vlans

E.

VLAN ACL Port ACL

F.

Switch Virtual Interface

G.

Port Security

 

Correct Answer: D

Explanation:

The problem here is that VLAN 10 is not configured on the proper interfaces on switch ASW1.

 

 

QUESTION 52

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?

 

A.

In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport mode access vlan 10 command.

B.

In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport access mode vlan 10 command.

C.

In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport vlan 10 access command.

D.

In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport access vlan 10 command.

 

Correct Answer: D

Explanation:

The problem here is that VLAN 10 is not configured on the proper interfaces on switch ASW1.

 

 

 

 

 

 

 

 

 

 

 

 

 

Ticket 3: OSPF Authentication (QUESTION 53 ~ QUESTION 55)

Topology Overview (Actual Troubleshooting lab design is for below network design)

 

Client Should have IP 10.2.1.3

EIGRP 100 is running between switch DSW1 & DSW2

OSPF (Process ID 1) is running between R1, R2, R3, R4

Network of OSPF is redistributed in EIGRP

BGP 65001 is configured on R1 with Webserver cloud AS 65002

HSRP is running between DSW1 & DSW2 Switches

 

The company has created the test bed shown in the layer 2 and layer 3 topology exhibits.

This network consists of four routers, two layer 3 switches and two layer 2 switches.

 

In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.

DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.

R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISP’s network. Because the company’s address space is in the private range.

R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network.

ASW1 and ASW2 are layer 2 switches.

NTP is enabled on all devices with 209.65.200.226 serving as the m
aster clock source.

The client workstations receive their IP address and default gateway via R4’s DHCP server.

The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.

 

In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.

DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.

The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary.

 

Recently the implementation group has been using the test bed to do a `proof-of-concept’ on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.

 

Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.

 

Each ticket has 3 sub questions that need to be answered & topology remains same.

Question-1 Fault is found on which device,

Question-2 Fault condition is related to,

Question-3 What exact problem is seen & what needs to be done for solution

 

=====================================================================

 

clip_image001

clip_image002

Client is unable to ping IP 209.65.200.241

 

Solution

Steps need to follow as below:

When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4

Ipconfig —– Client will be receiving IP address 10.2.1.3

IP 10.2.1.3 will be able to ping from R4 , R3, R2 but not from R1

 

clip_image004

 

Check for neighborship of ospf

sh ip ospf nei —– Only one neighborship is forming with R2 & i.e. with R3

Since R2 is connected to R1 & R3 with routing protocol ospf than there should be 2 neighbors seen but only one is seen

Need to check running config of R2 & R3 for interface

Sh run ————————– Interface Serial0/0/0/0.12 on R2

 

clip_image006

 

Sh run ————————– Interface Serial0/0/0/0 on R1

Change required: On R1, for IPV4 authentication of OSPF command is missing and required to configure —— ip ospf authentication message-diges
t

 

QUESTION 53

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?

 

A.

R1

B.

R2

C.

R3

D.

R4

E.

DSW1

F.

DSW2

G.

ASW1

H.

ASW2

 

Correct Answer: A

Explanation:

On R1, for IPV4 authentication of OSPF the command is missing and required to configure —— ip ospf authentication message-digest

 

 

QUESTION 54

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?

 

A.

BGP

B.

NTP

C.

IP NAT

D.

IPv4 OSPF Routing

E.

IPv4 OSPF Redistribution

F.

IPv6 OSPF Routing

G.

IPv4 layer 3 security

 

Correct Answer: D

Explanation:

On R1, for IPV4 authentication of OSPF the command is missing and required to configure —— ip ospf authentication message-digest

 

 

QUESTION 55

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?

 

A.

Enable OSPF authentication on the s0/0/0 interface using the ip ospf authentication message-digest command

B.

Enable OSPF routing on the s0/0/0 interface using the network 10.1.1.0 0.0.0.255 area 12 command.

C.

Enable OSPF routing on the s0/0/0 interface using the network 209.65.200.0 0.0.0.255 area 12 command.

D.

Redistribute the BGP route into OSPF using the redistribute BGP 65001 subnet command.

 

Correct Answer: A

Explanation:

On R1, for IPV4 authentication of OSPF the command is missing and required to configure—— ip ospf authentication message-digest

 

Ticket 4: BGP Neighbor (QUESTION 56 ~ QUESTION 58)

Topology Overview (Actual Troubleshooting lab design is for below network design)

 

Client Should have IP 10.2.1.3

EIGRP 100 is running between switch DSW1 & DSW2

OSPF (Process ID 1) is running between R1, R2, R3, R4

Network of OSPF is redistributed in EIGRP

BGP 65001 is configured on R1 with Webserver cloud AS 65002

HSRP is running between DSW1 & DSW2 Switches

 

The company has created the test bed shown in the layer 2 and layer 3 topology exhibits.

This network consists of four routers, two layer 3 switches and two layer 2 switches.

 

In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.

DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.

R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISP’s network. Because the company’s address space is in the private range.

R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network.

ASW1 and ASW2 are layer 2 switches.

NTP is enabled on all devices with 209.65.200.226 serving as the master clock source.

The client workstations receive their IP address and default gateway via R4’s DHCP server.

The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.

 

In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.

DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.

The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary.

 

Recently the implementation group has been using the test bed to do a `proof-of-concept’ on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.

 

Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.

 

Each ticket has 3 sub questions that need to be answered & topology remains same.

Question-1 Fault is found on which device,

Question-2 Fault condition is related to,

Question-3 What exact problem is seen & what needs to be done for solution

 

clip_image001[1]

clip_image002[1]

Client is unable to ping IP 209.65.200.241

 

Solution

Steps need to follow as below:

When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4

ipconfig —– Client will be receiving IP address 10.2.1.3

IP 10.2.1.3 will be able to ping from R4 , R3, R2, R1

Look for BGP Neighbourship

Sh ip bgp summary —– No O/P will be seen

Check for interface IP & ping IP 209.65.200.225 —- Reply will be received from Webserver interface

Look for peering IP address via sh run on R1 interface serial 0/0/1

 

clip_image007

clip_image008

 

Since we are receiving icmp packets from Webserver interface on R1 so peering IP address under router BGP is configured wrong IP but with correct AS nos.

Change required: On R1 under router BGP Change neighbor 209.56.200.226 remote-as 65002 statement to neighbor 209.65.200.226 remote-as 65002

 

 

QUESTION 56

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?

 

A.

R1

B.

R2

C.

R3

D.

R4

E.

DSW1

F.

DSW2

G.

ASW1

 

Correct Answer: A

Explanation:

The BGP neighbor statement is wrong on R1.

QUESTION 57

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?

 

A.

BGP

B.

NTP

C.

IP NAT

D.

IPv4 OSPF Routing

E.

IPv4 OSPF Redistribution

F.

IPv6 OSPF Routing

G.

IPv4 layer 3 security

 

Correct Answer: A

Explanation:

On R1 under router the BGP process Change neighbor 209.56.200.226 remote-as 65002 statement to neighbor 209.65.200.226 remote-as 65002

 

 

QUESTION 58

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?

 

A.

Under the BGP process, enter the bgp redistribute-internal command.

B.

Under the BGP process, bgp confederation identifier 65001command.

C.

Deleted the current BGP process and reenter all of the command using 65002 as the AS number.

D.

Under the BGP process, delete the neighbor 209.56.200.226 remote-as 65002 command and enter the neighbor 209.65.200.226 remote-as 65002 command.

 

Correct Answer: D

Explanation:

On R1 under router BGP change neighbor 209.56.200.226 remote-as 65002 statement to neighbor 209.65.200.226 remote-as 65002

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ticket 5: NAT ACL (QUESTION 59 ~ QUESTION 61)

Topology Overview (Actual Troubleshooting lab design is for below network design)

 

Client Should have IP 10.2.1.3

EIGRP 100 is running between switch DSW1 & DSW2

OSPF (Process ID 1) is running between R1, R2, R3, R4

Network of OSPF is redistributed in EIGRP

BGP 65001 is configured on R1 with Webserver cloud AS 65002

HSRP is running between DSW1 & DSW2 Switches

 

The company has created the test bed shown in the layer 2 and layer 3 topology exhibits.

This network consists of four routers, two layer 3 switches and two layer 2 switches.

 

In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.

DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.

R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISP’s network. Because the company’s address space is in the private range.

R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network.

ASW1 and ASW2 are layer 2 switches.

NTP is enabled on all devices with 209.65.200.226 serving as the master clock source.

The client workstations receive their IP address and default gateway via R4’s DHCP server.

The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.

 

In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.

DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.

The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary.

 

Recently the implementation group has been using the test bed to do a `proof-of-concept’ on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.

 

Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.

 

Each ticket has 3 sub questions that need to be answered & topology remains same.

Question-1 Fault is found on which device,

Question-2 Fault condition is related to,

Question-3 What exact problem is seen & what needs to be done for solution

 

clip_image001[2]

clip_image002[2]

Client is unable to ping IP 209.65.200.241

 

Solution

Steps need to follow as below:

When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4

Ipconfig —– Client will be receiving IP address 10.2.1.3

IP 10.2.1.3 will be able to ping from R4 , R3, R2, R1

Look for BGP Neighbourship

Sh ip bgp summary —– State of BGP will be in established state & will be able to receive I prefix (209.65.200.241)

As per troubleshooting we are able to ping ip 10.2.1.3 from R1 & BGP is also receiving prefix of webserver & we are able to ping the same from R1. Further troubleshooting needs to be done on R1 on serial 0/0/1

Check for running config. i.e sh run for interface serial 0/0/1..

 

clip_image010

!

clip_image012

!

 

From above snapshot we are able to see that IP needs to be PAT to serial 0/0/1 to reach web server IP (209.65.200.241). But in access-list of NAT IP allowed IP is 10.1.0.0/16 is allowed & need 10.2.0.0/16 to

As per troubleshooting we are able to ping ip 10.2.1.3 from R1 & BGP is also receiving prefix of web server & we are able to ping the same from R1. Its should be checked further for running config of interface for stopping

Change required: On R1 we need to add the client IP address for reachability to server to the access list that is used to specify which hosts get NATed.

 

 

QUESTION 59

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. On which device is the fault condition located?

 

A.

R1

B.

R2

C.

R3

D.

R4

E.

DSW1

F.

DSW2

G.

ASW1

 

Correct Answer: A

Explanation:

On R1 we need to add the client IP address for reachability to server to the access list that is used to specify which hosts get NATed.

 

 

QUESTION 60

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?

 

A.

BGP

B.

NTP

C.

IP NAT

D.

IPv4 OSPF Routing

E.

IPv4 OSPF Redistribution

F.

IPv6 OSPF Routing

G.

IPv4 layer 3 security

 

Correct Answer: C

Explanation:

On R1 we need to add the client IP address for reachability to server to the access list that is used to specify which hosts get NATed.

 

100% Free Download!
—Download Free Demo:300-135 Demo PDF
100% Pass Guaranteed!
Download 2017 Ensurepass 300-135 Full Exam PDF and VCE Q&As:269
—Get 10% off your purchase! Copy it:8GTC-8UIE-M1SC [2017.04.01-2017.04.30]

Ensurepass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF + VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Ensurepass IT Certification PDF and VCE

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com