[Free] 2017(Apr) Ensurepass Testking Cisco 300-135 Latest Dumps 41-50

Ensurepass
2017 April Cisco Official New Released 300-135 Q&As
100% Free Download! 100% Pass Guaranteed!
http://www.ensurepass.com/300-135.html

Troubleshooting and Maintaining Cisco IP Networks (TSHOOT)

 

QUESTION 41

Scenario:

You have been asked by your customer to help resolve issues in their routed network. Their network engineer has deployed HSRP. On closer inspection HSRP doesn’t appear to be operating properly and it appears there are other network problems as well. You are to provide solutions to all the network problems. Examine the configuration on R4. The routing table shows no entries for 172.16.10.0/24 and 172.16.20.0/24. Identify which of the following is the issue preventing route entries being installed on R4 routing table?

 

clip_image002

clip_image004

clip_image006

clip_image008

clip_image010

 

A.

HSRP issue between R4 and R2

B.

This is an OSPF issue between R4 and R2

C.

This is a DHCP issue between R4 and R2

D.

The distribute-list configured on R4 is blocking route entries

E.

The ACL configured on R4 is blocking inbound traffic on the interface connected to R2

 

Correct Answer: D

Explanation:

If we look at the configuration on R4 we see that there is a distribute list applied to OSPF, which blocks the 172.16.20.0/24 and 172.16.10.0/24 networks.

 

clip_image012

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 42

Scenario:

You have been asked by your customer to help resolve issues in their routed network. Their network engineer has deployed HSRP. On closer inspection HSRP doesn’t appear to be operating properly and it appears there are other network problems as well. You are to provide solutions to all the network problems. Examine the configuration on R5. Router R5 do not see any route entries learned from R4; what could be the issue?

 

clip_image013

clip_image014

clip_image015

clip_image016

clip_image017

 

A.

HSRP issue between R5 and R4

B.

There is an OSPF issue between R5 and R4

C.

There is a DHCP issue between R5 and R4

D.

The distribute-list configured on R5 is blocking route entries

E.

The ACL configured on R5 is blocking traffic for the subnets advertised from R4.

 

Correct Answer: B

Explanation:

If we issue the “show ip route” and “show ip ospf neighbor” commands on R5, we see that there are no learned OSPF routes and he has no OSPF neighbors.

 

clip_image019

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 43

Scenario:

A customer network engineer has edited their OSPF network configuration and now your customer is experiencing network issues. They have contacted you to resolve the issues and return the network to full functionality. The OSPF neighbour relationship has been lost between R1 and R3. What is causing this problem?

 

clip_image021

clip_image022

clip_image023

clip_image025

clip_image026

clip_image027

clip_image029

 

A.

The serial interface in R1 should be taken out of the shutdown state.

B.

A neighbor statement needs to be configured in R1 and R3 pointing at each other.

C.

The R1 network type should be changed to point-to-multipoint non-broadcast.

D.

The hello, dead and wait timers on R1 need to be reconfigured to match the values on R3.

 

Correct Answer: C

Explanation:

In order for two OSPF routers to become neighbors, they must have matching network types across the links. In this case, we see that R1 has been configured as non-broadcast and R3 is using point to point non-broadcast.

 

clip_image031

clip_image033

 

This can be seen by issuing the “show running-config” command on each router, or the “show ip ospf interface” command:

 

clip_image035

clip_image037

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 44

Scenario:

A customer network engineer has edited their OSPF network configuration and now your customer is experiencing network issues. They have contacted you to resolve the issues and return the network to full functionality. Connectivity from R3 to R4, R5 and R6 has been lost. How should connectivity be reestablished?

 

clip_image038

clip_image022[1]

clip_image023[1]

clip_image025[1]

clip_image026[1]

clip_image027[1]

clip_image039

 

A.

Configure R4 with a virtual link to 192.168.13.2

B.

Change the R3 and R4 hello-interval and retransmit-interface timers to zero so the link won’t go down.

C.

Add an OSPF network statement for 4.4.4.4 0.0.0.0 area 1 in R3

D.

Add an OSPF network statement for 192.168.34.3 0.0.0.255 area 2 in R3

E.

Add an OSPF network statement for 192.168.34.0 0.0.0.255 area 1 in R3

 

Correct Answer: E

Explanation:

Based on the network diagram, we know that a virtual link will need to be configured to logically connect area 2 to the back area 0. However, this is not the problem as we can see that R3 has been correctly configured to do this. It is, however, missing the network statement for the link to R4.

Here, we see that the link to R4 is using the 192.168.34.0 network, but that this network has not been added to OSPF

 

clip_image041

clip_image043

 

Based on the network diagram, this link should be added to Area 1, not Area 2.

 

 

 

 

 

 

 

QUESTION 45

Scenario:

A customer network engineer has edited their OSPF network configuration and now your customer is experiencing network issues. They have contacted you to resolve the issues and return the network to full functionality. After resolving the issues between R3 and R4. Area 2 is still experiencing routing issues. Based on the current router configurations, what needs to be resolved for routes to the networks behind R5 to be seen in the company intranet?

 

clip_image044

clip_image045

clip_image046

clip_image047

clip_image048

clip_image049

clip_image039[1]

 

A.

Configure R4 and R5 to use MD5 authentication on the Ethernet interfaces that connect to the common subnet.

B.

Configure Area 1 in both R4 and R5 to use MD5 authentication.

C.

Add ip ospf authentication-key 7 BEST to the R4 Ethernet interface that connects to R5 and ip ospf authentication-key 7 BEST to R5 Ethernet interface that connects to R4.

D.

Add ip ospf authentication-key CISCO to R4 Ethernet 0/1 and add area 2 authentication to the R4 OSPF routing process.

 

Correct Answer: D

Explanation:

Here, we see from the running configuration of R5 that OSPF authentication has been configured on the link to R4:

 

clip_image051

 

However, this has not been done on the link to R5 on R4:

 

clip_image053

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 46

Scenario:

A customer network engineer has edited their OSPF network configuration and now your customer is experiencing network issues. They have contacted you to resolve the issues and return the network to full functionality. The 6.6.0.0 subnets are not reachable from R4. how should the problem be resolved?

 

clip_image044[1]

clip_image045[1]

clip_image046[1]

clip_image047[1]

clip_image048[1]

clip_image049[1]

clip_image039[2]

 

A.

Edit access-list 46 in R6 to permit all the 6.6.0.0 subnets

B.

Apply access-list 46 in R6 to a different interface

C.

Apply access-list 1 as a distribute-list out under router ospf 100 in R4

D.

Remove distribute-list 64 out on R6

E.

Remove distribute-list 1 in ethernet 0/1 in R4

F.

Remove distribute-list 1 in ethernet 0/0 in R4

 

Correct Answer: D

Explanation:

Here we see from the running configuration of R6 that distribute list 64 is being used in the outbound direction to all OSPF neighbors.

 

clip_image055

 

However, no packets will match the 6.6.0.0 in this access list because the first line blocks all 6.0.0.0 networks, and since the 6.6.0.0 networks will also match the first line of this ACL, these OSPF networks will not be advertised because they are first denied in the first line of the ACL.

 

 

 

 

 

 

 

Ticket 1: Switch Port Trunk (QUESTION 47 ~ QUESTION 49)

Topology Overview (Actual Troubleshooting lab design is for below network design)

 

Client Should have IP 10.2.1.3

EIGRP 100 is running between switch DSW1 & DSW2

OSPF (Process ID 1) is running between R1, R2, R3, R4

Network of OSPF is redistributed in EIGRP

BGP 65001 is configured on R1 with Webserver cloud AS 65002

HSRP is running between DSW1 & DSW2 Switches

 

The company has created the test bed shown in the layer 2 and layer 3 topology exhibits.

This network consists of four routers, two layer 3 switches and two layer 2 switches.

 

In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.

DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.

R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISP’s network. Because the company’s address space is in the private range.

R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network.

ASW1 and ASW2 are layer 2 switches.

NTP is enabled on all devices with 209.65.200.226 serving as the master clock source.

The client workstations receive their IP address and default gateway via R4’s DHCP server.

The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.

 

In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.

DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.

The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary.

 

Recently the implementation group has been using the test bed to do a `proof-of-concept’ on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.

 

Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.

 

Each ticket has 3 sub questions that need to be answered & topology remains same.

Question-1 Fault is found on which device,

Question-2 Fault condition is related to,

Question-3 What exact problem is seen & what needs to be done for solution

 

clip_image056

clip_image057

Client is unable to ping IP 209.65.200.241

 

Solution

Steps need to follow as below:

When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4

Ipconfig —– Client will be getting 169.X.X.X

On ASW1 port Fa1/0/ 1 & Fa1/0/2 access port VLAN 10 was assigned which is using IP address 10.2.1.0/24

Sh run ——- & check for running config of int fa1/0/1 & fa1/0/2

====================================================

interface FastEthernet1/0/1switchport mode accessswitchport access vlan 10interface FastEthernet1/0/2switchport mode accessswitchport access vlan 10 ====================================================  We need to check on ASW 1 trunk port the trunk Po13 & Po23 were receiving VLAN 20 & 200 but not VLAN 10 so that switch could not get DHCP IP address and was failing to reach IP address of Internet

 

clip_image059

 

Change required: On ASW1 below change is required for switch-to-switch connectivity..

int range portchannel13,portchannel23 switchport trunk allowed vlan none switchport trunk allowed vlan 10,200

 

 

QUESTION 47

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been operated indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to Isolated the cause of this fault and answer the following questions. On which device is the fault condition located?

 

A.

R1

B.

R2

C.

R3

D.

R4

E.

DSW1

F.

DSW2

G.

ASW1

H.

ASW2

 

Correct Answer: G

Explanation:

Since the Clients are getting an APIPA we know that DHCP is not working. However, upon closer examination of the ASW1 configuration we can see that the problem is not with DHCP, but the fact that the trunks on the port channels are only allowing VLANs 1-9, when the clients belong to VLAN 10. VLAN 10 is not traversing the trunk on ASW1, so the problem is with the trunk configuration on ASW1.

 

 

QUESTION 48

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. The fault condition is related to which technology?

 

A.

NTP

B.

Switch-to-Switch Connectivity

C.

Access Vlans

D.

Port Security

E.

VLAN ACL / Port ACL

F.

Switch Virtual Interface

 

Correct Answer: B

Explanation:

Since the Clients are getting an APIPA we know that DHCP is not working. However, upon closer examination of the ASW1 configuration we can see that the problem is not with DHCP, but the fact that the trunks on the port channels are only allowing VLANs 1-9, when the clients belong to VLAN 10. VLAN 10 is not traversing the trunk on ASW1, so the problem is with switch to switch connectivity, specifically the trunk configuration on ASW1.

 

 

QUESTION 49

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?

 

A.

In Configuration mode, using the interface port-channel 13 command, then configure switchport trunk allowed vlan none followed by switchport trunk allowed vlan 20,200 commands.

B.

In Configuration mode, using the interface port-channel 13, port-channel 23, then configure switchport trunk none allowed vlan none followed by switchport trunk allowed vlan 10,200 commands.

C.

In Configuration mode, using the interface port-channel 23 command, then configure switchport trunk allowed vlan none followed by switchport trunk allowed vlan 20,200 commands.

D.

In Configuration mode, using the interface port-channel 23, port-channel, then configure switchport trunk allowed vlan none followed by switchport trunk allowed vlan 10,20,200 commands.

 

Correct Answer: B

Explanation:

We need to allow VLANs 10 and 200 on the trunks to restore full connectivity. This can be accomplished by issuing the “switchport trunk allowed vlan 10,200” command on the port channels used as trunks in DSW1.

Ticket 2: ACCESS VLAN (QUESTION 50 ~ QUESTION 52)

Topology Overview (Actual Troubleshooting lab design is for below network design)

 

Client Should have IP 10.2.1.3

EIGRP 100 is running between switch DSW1 & DSW2

OSPF (Process ID 1) is running between R1, R2, R3, R4

Network of OSPF is redistributed in EIGRP

BGP 65001 is configured on R1 with Webserver cloud AS 65002

HSRP is running between DSW1 & DSW2 Switches

 

The company has created the test bed shown in the layer 2 and layer 3 topology exhibits.

This network consists of four routers, two layer 3 switches and two layer 2 switches.

 

In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.

DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.

R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISP’s network. Because the company’s address space is in the private range.

R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network.

ASW1 and ASW2 are layer 2 switches.

NTP is enabled on all devices with 209.65.200.226 serving as the master clock source.

The client workstations receive their IP address and default gateway via R4’s DHCP server.

The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.

 

In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.

DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.

The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary.

 

Recently the implementation group has been using the test bed to do a `proof-of-concept’ on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.

 

Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.

 

Each ticket has 3 sub questions that need to be answered & topology remains same.

Question-1 Fault is found on which device,

Question-2 Fault condition is related to,

Question-3 What exact problem is seen & what needs to be done for solution

 

clip_image056[1]

clip_image057[1]

Client is unable to ping IP 209.65.200.241

 

Solution

Steps need to follow as below:

When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4

Ipconfig —– Client will be getting 169.X.X.X

On ASW1 port Fa1/0/ 1 & Fa1/0/2 access port VLAN 10 was assigned which is using IP address 10.2.1.0/24

Sh run ——- & check for running config of int fa1/0/1 & fa1/0/2

 

====================================================

 

clip_image060

 

====================================================

 

Here we are not able to see access Vlan10 configured for Port Fa1/0/1 & Fa1/0/2

Change required: On ASW1, for configuring Access Vlan under interface fa1/0/1 & 1/0/2 we have to enable command switchport access vlan 10

 

 

QUESTION 50

The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address. Use the supported commands to isolated the cause of this fault and answer the following questions. What is the solution to the fault condition?

 

A.

R1

B.

R2

C.

R3

D.

R4

E.

DSW1

F.

DSW2

G.

ASW1

H.

ASW2

 

Correct Answer: G

Explanation:

The problem here is that VLAN 10 is not configured on the proper interfaces on switch ASW1.

 

100% Free Download!
—Download Free Demo:300-135 Demo PDF
100% Pass Guaranteed!
Download 2017 Ensurepass 300-135 Full Exam PDF and VCE Q&As:269
—Get 10% off your purchase! Copy it:8GTC-8UIE-M1SC [2017.04.01-2017.04.30]

Ensurepass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF + VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Ensurepass IT Certification PDF and VCE

HOT EXAM!
Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com