[Free] 2017(Apr) Ensurepass Testking Cisco 300-135 Latest Dumps 31-40

Ensurepass
2017 April Cisco Official New Released 300-135 Q&As
100% Free Download! 100% Pass Guaranteed!
http://www.ensurepass.com/300-135.html

Troubleshooting and Maintaining Cisco IP Networks (TSHOOT)

 

QUESTION 31

Refer to exhibit. The tunnel between R2 and R5 is not coming up. R2, R4 and R5 do not have any routing information sources other than OSPF and no route filtering is implemented anywhere in the network. Which two actions fix the issue? (Choose Two)

 

clip_image002

 

A.

Redistribute connected routes to OSPF on R5.

B.

Change the tunnel destination on R2 to 192.168.2.1

C.

Advertise interface Lo0 to OSPF on R5.

D.

Configure a static route on R5 to 2.2.2.2 via 192.168.2.1

E.

Fix the OSPF adjacency issue between R2 and r5.

 

Correct Answer: AC

Explanation:

In order for the tunnel to be established between R2-R5 ,the R2 should have a path for the 5.5.5.5/32 route in its own routing table , and because the ospf is the only routing protocol here , so R5 has to advertise the route 5.5.5.5/32, and that is possible through these option:

 

1-redistribute connected route to ospf on R5

2-Advertise interface lo0 to OSPF on R5

 

For knowing more about the rules for the gre channel to be established, check the link below:

 

http://www.cisco.com/c/en/us/support/docs/ip/generic-routing-encapsulation-gre/118361-technote-gre-00.html

 

 

QUESTION 32

Refer to exhibit. After a junior technician configures a new branch office GRE tunnel, which step is missing from the configuration to pass traffic through tunnel on Router 1?

 

clip_image004

 

A.

static route to 10.0.3.0/24 via 10.0.1.1

B.

static route to 10.0.3.0/24 via 10.0.2.1

C.

static route to 10.0.3.0/24 via 190.0.4.1

D.

static route to 10.0.3.0/24 via 190.0.4.2

 

Correct Answer: D

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 33

A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems. PC2 in VLAN 200 is unable to ping the gateway address 172.16.200.1; identify the issue.

 

clip_image006

clip_image008

clip_image010

clip_image012

clip_image014

 

A.

VTP domain name mismatch on SW4

B.

VLAN 200 not configured on SW1

C.

VLAN 200 not configured on SW2

D.

VLAN 200 not configured on SW4

 

Correct Answer: C

Explanation:

By looking at the configuration for SW2, we see that it is missing VLAN 200, and the “switchport access vlan 200” command is missing under interface eth 0/0:

 

clip_image016

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 34

A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems. Which of statement is true regarding STP issue identified with switches in the given topology?

 

clip_image017

clip_image018

clip_image019

clip_image020

clip_image021

 

A.

Loopguard configured on the New_Switch places the ports in loop inconsistent state

B.

Rootguard configured on SW1 places the ports in root inconsistent state

C.

Bpduguard configured on the New_Switch places the access ports in error-disable

D.

Rootguard configured on SW2 places the ports in root inconsistent state

 

Correct Answer: A

Explanation:

On the new switch, we see that loopguard has been configured with the “spanning-tree guard loop” command.

 

clip_image022

 

The loop guard feature makes additional checks. If BPDUs are not received on a non-designated port, and loop guard is enabled, that port is moved into the STP loop-inconsistent blocking state, instead of the listening / learning / forwarding state. Without the loop guard feature, the port assumes the designated port role. The port moves to the STP forwarding state and creates a loop.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 35

A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems. You have configured PVST+ load balancing between SW1 and the New_Switch in such a way that both the links E2/2 and E2/3 are utilized for traffic flow, which component of the configuration is preventing PVST+ load balancing between SW1 and SW2 links?

 

clip_image023

clip_image024

clip_image025

clip_image026

clip_image027

 

A.

Port priority configuration on SW1

B.

Port priority configuration on the New_Switch

C.

Path cost configuration on SW1

D.

Path cost configuration on the New_Switch

 

Correct Answer: D

Explanation:

Here is the configuration found on the New_Switch:

 

clip_image028

 

This causes the port cost for link eth 1/3 to increase the path cost to 250 for all VLANs, making that link less preferred so that only eth 1/2 will be used.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

QUESTION 36

A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems. Refer to the topology. SW1 Switch Management IP address is not pingable from SW4. What could be the issue?

 

clip_image023[1]

clip_image029

clip_image025[1]

clip_image030

clip_image031

 

A.

Management VLAN not allowed in the trunk links between SW1 and SW4

B.

Management VLAN not allowed in the trunk links between SW1 and SW2

C.

Management VLAN not allowed in the trunk link between SW2 and SW4

D.

Management VLAN ip address on SW4 is configured in wrong subnet

E.

Management VLAN interface is shutdown on SW4

 

Correct Answer: D

Explanation:

In the network, VLAN 300 is called the Management VLAN. Based on the configurations shown below, SW1 has VLAN 300 configured with the IP address of 192.168.10.1/24, while on SW4 VLAN 300 has an IP address of 192.168.100.4/24, which is not in the same subnet.

 

clip_image033

clip_image035

QUESTION 37

You have been brought in to troubleshoot an EIGRP network. A network engineer has made configuration changes to the network rendering some locations unreachable. You are to locate the problem and suggest solution to resolve the issue. R5 has become partially isolated from the remainder of the network. R5 can reach devices on directly connected networks but nothing else. What is causing the problem?

 

clip_image037

clip_image039

clip_image041

clip_image043

clip_image045

clip_image047

clip_image049

 

A.

An outbound distribute list in R3

B.

Inbound distribute lists in R5

C.

An outbound distribute list in R6

D.

Incorrect EIGRP routing process ID in R5

 

Correct Answer: B

Explanation:

Here we see that distribute list 3 has been applied to EIGRP on router R%, but access-list 3 contains only deny statements so this will effectively block all routing advertisements from its two EIGRP neighbors, thus isolating R5 from the rest of the EIGRP network:

 

clip_image050

clip_image052

 

 

 

 

 

 

 

QUESTION 38

Scenario:

You have been brought in to troubleshoot an EIGRP network. You have resolved the initial issue between routers R2 and R4, but another issue remains. You are to locate the problem and suggest solution to resolve the issue. The customer has disabled access to the show running-config command. The network segment between R2 and R4 has become disconnected from the remainder of the network. How should this issue be resolved?

 

clip_image053

clip_image039[1]

clip_image041[1]

clip_image054

clip_image045[1]

clip_image047[1]

clip_image049[1]

 

A.

Change the autonomous system number in the remainder of the network to be consistent with R2 and R4.

B.

Move the 192.168.24.0 network to the EIGRP 1 routing process in R2 and R4.

C.

Enable the R2 and R4 router interfaces connected to the 192.168.24.0 network.

D.

Remove the distribute-list command from the EIGRP 200 routing process in R2.

E.

Remove the distribute-list command from the EIGRP 100 routing process in R2.

 

Correct Answer: B

Explanation:

When issuing the “show ip eigrp neighbor” command (which is about the only command that it lets you do in this question) you will see that all other routers are configured for EIGRP AS 1. However, the 192.16824.0 network between R2 and R4 is incorrectly configured for EIGRP AS 100:

 

clip_image056

clip_image058

 

 

 

 

 

 

 

 

 

 

 

QUESTION 39

Scenario:

You have been asked by your customer to help resolve issues in their routed network. Their network engineer has deployed HSRP. On closer inspection HSRP doesn’t appear to be operating properly and it appears there are other network problems as well. You are to provide solutions to all the network problems. You have received notification from network monitoring system that link between R1 and R5 is down and you noticed that the active router for HSRP group 1 has not failed over to the standby router for group 1. You are required to troubleshoot and identify the issue.

 

clip_image060

clip_image039[2]

clip_image061

clip_image045[2]

clip_image047[2]

 

A.

There is an HSRP group track command misconfiguration

B.

There is an HSRP group priority misconfiguration

C.

There is an HSRP authentication misconfiguration

D.

There is an HSRP group number mismatch

E.

This is not an HSRP issue; this is routing issue.

 

Correct Answer: A

Explanation:

When looking at the HSRP configuration of R1, we see that tracking has been enabled, but that it is not tracking the link to R5, only the link to R2:

 

clip_image063

 

R1 should be tracking the Eth 0/1 link, not 0/0 to achieve the desired affect.

 

 

QUESTION 40

Scenario:

You have been asked by your customer to help resolve issues in their routed network. Their network engineer has deployed HSRP. On closer inspection HSRP doesn’t appear to be operating properly and it appears there are other network problems as well. You are to provide solutions to all the network problems.

 

The following debug messages are noticed for HSRP group 2. But still neither R1 nor R2 has identified one of them as standby router. Identify the reason causing the issue.

Note: only show commands can be used to troubleshoot the ticket.

 

R1#

‘Mar 26 11:17:39.234: HSRP: Et1/0 Grp 2 Hello out 172.16.20.2 Active pri 100 vIP 172.16.20.254

‘Mar 26 11:17:40.034: HSRP: EtO/0 Grp 1 Hello out 172.16.10.2 Active prj 130 vIP 172.16.10.254

R1#

‘Mar 26 11:17:40.364: HSRP: EtO/0 Grp 1 Hello in 172.16.10.1 Standby pri 100 vIP 172.16.10.254

R1#

‘Mar 26 11:17:41.969: HSRP: Et1/0 Grp 2 Hello out 172.16.20.2 Active pri 100 vIP 172.16.20.254

‘Mar 26 11:17:42.719: HSRP: EtO/0 Grp 1 Hello out 172.16.10.2 Active prj 130 vIP 172.16.10.254

‘Mar 26 11:17:42.918: HSRP: EtO/0 Grp 1 Hello in 172.16.10.1 Standby pri 100 vIP 172.16.10.254

R1#

‘Mar 26 11:17:44.869: HSRP: Et1/0 Grp 2 Hello out 172.16.20.2 Active pri 100 vIP 172.16.20.254

‘Mar 26 11:17:45.485: HSRP: EtO/0 Grp 1 Hello out 172.16.10.2 Active prj 130 vIP 172.16.10.254

‘Mar 26 11:17:45.718: HSRP: EtO/0 Grp 1 Hello in 172.16.10.1 Standby pri 100 vIP 172.16.10.254

R1#

‘Mar 26 11:17:47.439: HSRP: Et1/0 Grp 2 Hello out 172.16.20.2 Active pri 100 vIP 172.16.20.254

‘Mar 26 11:17:48.252: HSRP: EtO/0 Grp 1 Hello in 172.16.10.1 Standby pri 100 vIP 172.16.10.254

‘Mar 26 11:17:48.322: HSRP: EtO/0 Grp 1 Hello out 172.16.10.2 Active prj 130 vIP 172.16.10.254

R1#

‘Mar 26 11:17:50.389: HSRP: Et1/0 Grp 2 Hello out 172.16.20.2 Active pri 100 vIP 172.16.20.254

‘Mar 26 11:17:50.735: HSRP: EtO/0 Grp 1 Hello in 172.16.10.1 Standby pri 100 vIP 172.16.10.254

‘Mar 26 11:17:50.921: HSRP: EtO/0 Grp 1 Hello out 172.16.10.2 Active prj 130 vIP 172.16.10.254

R1#

‘Mar 26 11:17:53.089: HSRP: Et1/0 Grp2 Hello out 172.16.20.2 Active pri 100 vIP 172.16.20.254

‘Mar 26 11:17:53.338: HSRP: EtO/0 Grp 1 Hello out 172.16.10.2 Active pri130vlP 172.16.10.254

‘Mar 26 11:17:53.633: HSRP: EtO/0 Grp 1 Hello in 172.16.10.1 Standby pri 100 vIP 172.16.10.254

 

clip_image060[1]

clip_image039[3]

clip_image064

clip_image065

clip_image066

 

A.

HSRP group priority misconfiguration.

B.

There is an HSRP authentication misconfiguration.

C.

There is an HSRP group number mismatch.

D.

This is not an HSRP issue: this is DHCP issue.

E.

The ACL applied to interface is blocking HSRP hello packet exchange.

 

Correct Answer: E

Explanation:

On R1 we see that access list 102 has been applied to the Ethernet 1/0 interface:

 

clip_image068

clip_image070

 

This access list is blocking all traffic to the 224.0.0.102 IP address, which is the multicast address used by HSRP.

 

100% Free Download!
—Download Free Demo:300-135 Demo PDF
100% Pass Guaranteed!
Download 2017 Ensurepass 300-135 Full Exam PDF and VCE Q&As:269
—Get 10% off your purchase! Copy it:8GTC-8UIE-M1SC [2017.04.01-2017.04.30]

Ensurepass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF + VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Ensurepass IT Certification PDF and VCE

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com