[Free] 2017(Apr) Ensurepass Testking Cisco 300-135 Latest Dumps 21-30

Ensurepass
2017 April Cisco Official New Released 300-135 Q&As
100% Free Download! 100% Pass Guaranteed!
http://www.ensurepass.com/300-135.html

Troubleshooting and Maintaining Cisco IP Networks (TSHOOT)

 

QUESTION 21

The following commands are issued on a Cisco Router:

 

Router(configuration)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1

Router(configuration)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1

Router(configuration)#exit

Router#debug ip packet 199

 

What will the debug output on the console show?

 

A.

All IP packets passing through the router

B.

Only IP packets with the source address of 10.1.1.1

C.

All IP packets from 10.1.1.1 to 172.16.1.1

D.

All IP Packets between 10.1.1.1 and 172.16.1.1

 

Correct Answer: D

 

 

QUESTION 22

What level of logging is enabled on a Router where the following logs are seen?

 

%LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

 

A.

alerts

B.

critical

C.

errors

D.

notifications

 

Correct Answer: D

 

 

QUESTION 23

You have the followings commands on your Cisco Router:

 

ip ftp username admin

ip ftp password backup

 

You have been asked to switch from FTP to HTTP. Which two commands will you use to replace the existing commands?

 

A.

ip http username admin

B.

ip http client username admin

C.

ip http password backup

D.

ip http client password backup

E.

ip http server username admin

F.

ip http server password backup

 

Correct Answer: BD

 

 

QUESTION 24

You have 2 NTP servers in your network – 10.1.1.1 and 10.1.1.2. You want to configure a Cisco router to use 10.1.1.2 as its NTP server before falling back to 10.1.1.1. Which commands will you use to configure the router?

 

A.

ntp server 10.1.1.1

ntp server 10.1.1.2

B.

ntp server 10.1.1.1

ntp server 10.1.1.2 primary

C.

ntp server 10.1.1.1

ntp server 10.1.1.2 prefer

D.

ntp server 10.1.1.1 fallback

ntp server 10.1.1.2

 

Correct Answer: C

 

 

QUESTION 25

The following command is issued on a Cisco Router:

 

Router(configuration)#logging console warnings

 

Which alerts will be seen on the console?

 

A.

Warnings only

B.

debugging, informational, notifications, warnings

C.

warnings, errors, critical, alerts, emergencies

D.

notifications, warnings, errors

E.

warnings, errors, critical, alerts

 

Correct Answer: C

 

 

QUESTION 26

Which two of the following options are categories of Network Maintenance tasks?

 

A.

Firefighting

B.

Interrupt-driven

C.

Policy-based

D.

Structured

E.

Foundational

 

Correct Answer: BD

 

 

 

QUESTION 27

Refer to the Exhibit. Which output is expected in the blank line for the OSPF adjacency process?

 

clip_image002

 

A.

DOWN

B.

EXSTART

C.

EXCHANGE

D.

LOADING

 

Correct Answer: B

Explanation:

You can check the output of “debug ip ospf adj” here:

 

clip_image004

 

 

QUESTION 28

You are troubleshooting an issue with a GRE tunnel between R1 and R2 and find that routing is OK on all intermediary routers. The tunnel is up on R1, but down on R2. Which two possible issues can prevent the tunnel from coming up? (Choose Two)

 

A.

The tunnel does not come up unless traffic is sent through it.

B.

The tunnel source interface is down on R2.

C.

No specific route interface is down on R2.

D.

R2 does not know how to reach the tunnel destination.

E.

The tunnel keep alive timer doesn’t match on R1 and R2.

 

Correct Answer: BD

Explanation:

Four Different Tunnel States

There are four possible states in which a GRE tunnel interface can be:

 

1. Up/up – This implies that the tunnel is fully functional and passes traffic. It is both adminstratively up and it’s protocol is up as well.

2. Adminstratively down/down – This implies that the interface has been administratively shut down.

3. Up/down – This implies that, even though the tunnel is administratively up, something causes the line protocol on the interface to be down.

4. Reset/down – This is usually a transient state when the tunnel is reset by software. This usually happens when the tunnel is misconfigured with a Next Hop Server (NHS) that is it’s own IP address.

When a tunnel interface is first created and no other configuration is applied to it, the interface is not shut by default:

 

clip_image006

clip_image008

clip_image010

 

QUESTION 29

Refer to the exhibit. Which two statements are correct? (Choose Two)

 

clip_image011

 

A.

The source device has name resolution configured.

B.

The source device is using two routes for the destination, learned from different protocols.

C.

A device on the path is introducing considerable delay.

D.

The source device is loading balancing traffic.

 

Correct Answer: AD

Explanation:

Router traces domain name (cisco.com) and it gets ICMP answers, so name resolution has happened.

Per hop output shows 2 lines, hence 2 active paths exist.

 

 

QUESTION 30

Refer to exhibit. R1 and R2 are directly connected using interface Ethernet0/0 on both sides. R1 and R2 were not becoming adjacent, so you have just configured R2 interface Ethernet0/0 as network type broadcast. Which two statements are true?

 

A.

Three OSPF routers are in the network segment connected to 192.168.1.0/24

B.

R1 installs a route to 2.2.2.2/32 as O.

C.

R2 is not an OSPF ABR.

D.

R1 interface Ethernet0/0 is configured as OSPF type point to point.

E.

R1 installs a route to 2.2.2.2/32 as O IA.

F.

both routers R1 and R2 are neighbors and R2 IS BDR.

Correct Answer: EF

Explanation:

For the Answer 5 “R1 installs a route to 2.2.2.2/32 as O IA”:

That because the route 2.2.2.2/32 belong to another area (area1). -for the Answer 6 “both routers R1 and R2 are neighbors, and R2 IS BDR”:

Here clearly the question, say that R1 and R2 are not adjacent, but that not mean they are not neighbors, from the output of “show ip ospf neighbor” command we can see clearly that routers R1 and R2 are neighbors, and actually the R2 is BDR.

There different between adjacent and neighbor, neighbors” and “adjacent”. Two terminologies that doesn’t mean the same thing, but can often be misused in a discussion. Neighbors in this case means “show up as neighbors while using the show ip ospf neighbors command”. While “adjacent” means they are fully exchanging topology information.

For further information check the links below:

https://learningnetwork.cisco.com/message/564573#564573 http://blog.ine.com/2008/01/08/understanding-ospf-network-types/

 

100% Free Download!
—Download Free Demo:300-135 Demo PDF
100% Pass Guaranteed!
Download 2017 Ensurepass 300-135 Full Exam PDF and VCE Q&As:269
—Get 10% off your purchase! Copy it:8GTC-8UIE-M1SC [2017.04.01-2017.04.30]

Ensurepass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF + VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Ensurepass IT Certification PDF and VCE

HOT EXAM!
Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com