[Free] 2017(Apr) Ensurepass Testking Cisco 300-101 Latest Dumps 101-110

Ensurepass
2017 April Cisco Official New Released 300-101 Q&As
100% Free Download! 100% Pass Guaranteed!
http://www.ensurepass.com/300-101.html

Implementing Cisco IP Routing (ROUTE v2.0)

 

QUESTION 101

Which Cisco VPN technology uses AAA to implement group policies and authorization and is also used for the XAUTH authentication method?

 

A.

DMVPN

B.

Cisco Easy VPN

C.

GETVPN

D.

GREVPN

 

Correct Answer: B

 

 

 

 

 

QUESTION 102

Which statement about dual stack is true?

 

A.

Dual stack translates IPv6 addresses to IPv4 addresses.

B.

Dual stack means that devices are able to run IPv4 and IPv6 in parallel.

C.

Dual stack translates IPv4 addresses to IPv6 addresses.

D.

Dual stack changes the IP addresses on hosts from IPv4 to IPv6 automatically.

 

Correct Answer: B

 

 

QUESTION 103

Refer to the exhibit. The command is executed while configuring a point-to-multipoint Frame Relay interface. Which type of IPv6 address is portrayed in the exhibit?

 

clip_image001

 

A.

link-local

B.

site-local

C.

global

D.

multicast

 

Correct Answer: A

 

 

QUESTION 104

Which statement about the NPTv6 protocol is true?

 

A.

It is used to translate IPv4 prefixes to IPv6 prefixes.

B.

It is used to translate an IPv6 address prefix to another IPv6 prefix.

C.

It is used to translate IPv6 prefixes to IPv4 subnets with appropriate masks.

D.

It is used to translate IPv4 addresses to IPv6 link-local addresses.

 

Correct Answer: B

 

 

QUESTION 105

Which parameter in an SNMPv3 configuration offers authentication and encryption?

 

A.

auth

B.

noauth

C.

priv

D.

secret

 

Correct Answer: C

 

 

QUESTION 106

How does an IOS router process a packet that should be switched by Cisco Express Forwarding without an FIB entry?

 

A.

by forwarding the packet

B.

by dropping the packet

C.

by creating a new FIB entry for the packet

D.

by looking in the routing table for an alternate FIB entry

 

Correct Answer: B

 

 

QUESTION 107

A network administrator is troubleshooting a DMVPN setup between the hub and the spoke. Which action should the administrator take before troubleshooting the IPsec configuration?

 

A.

Verify the GRE tunnels.

B.

Verify ISAKMP.

C.

Verify NHRP.

D.

Verify crypto maps.

 

Correct Answer: A

 

 

QUESTION 108

Which IPv6 address type is seen as the next-hop address in the output of the show ipv6 rip RIPng database command?

 

A.

link-local

B.

global

C.

site-local

D.

anycast

E.

multicast

 

Correct Answer: A

 

 

QUESTION 109

Refer to the exhibit. The network setup is running the RIP routing protocol. Which two events will occur following link failure between R2 and R3? (Choose two.)

 

clip_image002

 

A.

R2 will advertise network 192.168.2.0/27 with a hop count of 16 to R1.

B.

R2 will not send any advertisements and will remove route 192.168.2.0/27 from its routing table.

C.

R1 will reply to R2 with the advertisement for network 192.168.2.0/27 with a hop count of 16.

D.

After communication fails and after the hold-down timer expires, R1 will remove the 192.168.2.0/27 route from its routing table.

E.

R3 will not accept any further updates from R2, due to the split-horizon loop prevention mechanism.

 

Correct Answer: AC

 

 

QUESTION 110

A network engineer is trying to modify an existing active NAT configuration on an IOS router by using the following command:

 

(config)# no ip nat pool dynamic-nat-pool 192.1.1.20 192.1.1.254 netmask 255.255.255.0

 

Upon entering the command on the IOS router, the following message is seen on the console:

 

%Dynamic Mapping in Use, Cannot remove message or the %Pool outpool in use, cannot destroy

 

What is the least impactful method that the engineer can use to modify the existing IP NAT configuration?

 

A.

Clear the IP NAT translations using the clear ip nat traffic * ” command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

B.

Clear the IP NAT translations using the clear ip nat translation * ” command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

C.

Clear the IP NAT translations using the reload command on the router, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

D.

Clear the IP NAT translations using the clear ip nat table * ” command, then replace the NAT configuration quickly, before any new NAT entries are populated into the translation table due to active NAT traffic.

 

Correct Answer: B

 

100% Free Download!
—Download Free Demo:300-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Ensurepass 300-101 Full Exam PDF and VCE Q&As:212
—Get 10% off your purchase! Copy it:8GTC-8UIE-M1SC [2017.04.01-2017.04.30]

Ensurepass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF + VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Ensurepass IT Certification PDF and VCE

HOT EXAM!
Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com